Types of patterns:
The following factors affect the choice of a pattern.
(i) Number of Castings to be produced.
(ii) Size and complexity of the shape and size of casting
(iii) Type of molding and castings method to be used.
(iv) Machining operation
(v) Characteristics of castings
Different types of patterns:
The common types of patterns are:
1) Single piece pattern
2) Split piece pattern
3) Loose piece pattern
4) Gated pattern
5) Match pattern
6) Sweep pattern
7) Cope and drag pattern
8) Skeleton pattern
9) Shell pattern
10) Follow board pattern
Figure 1: Single piece, Split, Match-plate, Cope and Drag Pattern
Single piece pattern:
This is the simplest type of pattern, exactly like the desired casting. For making a mould, the pattern is accommodated either in cope or drag.
Used for producing a few large castings, for example, stuffing box of steam engine.
Split pattern:
These patterns are split along the parting plane (which may be flat or irregular surface) to facilitate the extraction of the patternout of the mould before the pouring operation. For a more complex casting, the pattern may be split in more than two parts.
Loose piece pattern:
When a one piece solid pattern has projections or back drafts which lie above or below the parting plane, it is impossible to with drawit from the mould. With such patterns, the projections are made with the help of loose pieces. One drawback of loose feces is that their shifting is possible during ramming.
Figure: Loose piece pattern
Gated pattern:
A gated pattern is simply one or more loose patterns having attached gates and runners.Because of their higher cost, these patterns are used for producing small castings in mass production systems and on molding machines.
Figure: Gated pattern
Match plate pattern:
A match plate pattern is a split pattern having the cope and drags portions mounted on opposite sides of a plate (usually metallic), called the "match plate" that conforms to the contour of the parting surface.
The gates and runners are also mounted on the match plate, so that very little hand work is required. This results in higher productivity. This type of pattern is used for a large number of castings.
Piston rings of I.C. engines are produced by this process.
Please Read : Match - Plate Pattern complete guide with diagram.
Sweep pattern:
A sweep is a section or board (wooden) of proper contour that is rotated about one edge to shape mould cavities having shapes of rotational symmetry. This type of pattern is used when a casting of large size is to be produced in a short time. Large kettles of C.I. are made by sweep patterns.
Figure: Sweep pattern
Cope and drag pattern:
A cope and drag pattern is a split pattern having thecope and drag portions each mounted on separate match plates. These patterns are used when in the production of large castings; the complete moulds are too heavy and unwieldy to be handled by a single worker.
Skeleton pattern:
For large castings having simple geometrical shapes, skeleton patterns are used. Just like sweep patterns, these are simple wooden frames that outline the shape of the part to be cast and are also used as guides by the molder in the hand shaping of the mould.
This type of pattern is also used in pit or floor molding process.
Figure: Skeleton pattern
Shell pattern:
Figure: Shell pattern
Follow board pattern:
A follow board is not a pattern but is a device (wooden board) used for various purposes.
Figure : Follow board pattern
Please read :
Comparison of Casting processes Advantages and Disadvantages of Centrifugal casting process
Type of molding sand in casting process
Natural and synthetic sand properties for molding process
Different types of casting defects
Different Types of Welding Defects
Different Sand Casting Process
Thanks (y)
ReplyDeletesuper,fantastic,..........................................
ReplyDeleteTnx
ReplyDeleteit is neccessary to mechanical
ReplyDeletewill u please tell me example for each pattern
ReplyDeletethanxxxx...
ReplyDeletethnx
ReplyDeleteThxπππππ
ReplyDeleteThis blog has helped me alot to mk my concepts clear related to pattern making.
ReplyDeleteThank you Mr. Blogger
thankx....
ReplyDeletethank you
ReplyDeleteEnter your comment...thanks
ReplyDeleteThank you
ReplyDeletesuper
ReplyDeleteNice
ReplyDeleteVery helpful.
ReplyDeleteThanx
ReplyDeleteI need at least 20.
ReplyDeletesuper
ReplyDeleteThanks, it's made it very clear, I am very great full.
ReplyDeleteThanks
ReplyDeleteInitially I was afraid of it but now with this explanation it became easy
ReplyDeleteThanks a lot
ReplyDeleteThanks
ReplyDeleteThx
ReplyDeleteThanks
ReplyDeletethanks
ReplyDeleteThank you
ReplyDeleteVery good.
ReplyDeleteIf Some examples given it will be better
Understanding for all technical staffs.
Thanks
ReplyDeletePlease add what is master pattern with diagram ?
ReplyDeletePlease add what is master pattern with diagram?
ReplyDeleteThanks
ReplyDeletevery useful thank you
ReplyDeleteThanksπͺ
ReplyDeletethankd
ReplyDelete